SWANS / HiVi In-Wall Speaker
For covered installations Swans also offers high-quality solutions
without compromises in sound.
Features:
Adjustable fabric tweeters powered by neodymium magnets.
The very pleasant sounding high resolution silk calottes are 30° swiveling and can be tuned ideal to almost any listening position. Because of the custom front panel a very smooth dispersion with a large "sweet spot" can be achieved.
High-quality duplexers:
A custom adjusted duplexer with high-quality components was given each system. Depending on the model, 6, 12 or 18 db versions were used.
The tweeters are secured against overload by automatically reseting protection circuits and can be adjusted in three levels, depending on place of installation and acoustics.
Robust and practicable design - the framework consists of paintable long-life PP-plastic, all metal parts are made of oxidation-resistant aluminum or stainless steel. The very robust chassis were designed for a installation with an undefined volume and can also be optimized as a full-range system. High-quality port terminals are used, which ensure optimal contact at any time.
Grids, installation templates, accessories and painting covers are included in every system.
VX5-W
5.25” 2-way In-Wall Speaker
Woofer: 5.25” PP cone, rubber surround, 12.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 0.8" Silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion
Crossover: Phonalic PCB board, 12dB woofer section, 18dB tweeter section, Polymide auto protective reset switch for tweeter
Frequency Response: 50Hz- 20KHz
Sensitivity: 87dB
Recommended amplifier power: 10-80 watts
Impedance: 8 ohm jumper
Cut Out Size: 10.473"X7.126"
VX6-W
6.5” 2-way In-Wall Speaker
Woofer: 6.5” PP cone, rubber surround, 18.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 1" Silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion Crossover: Phonalic PCB board, 6dB woofer section, 6dB tweeter section, Polymide auto protective switch for tweeter
Frequency Response: 50Hz- 20KHz
Sensitivity: 88dB
Recommended amplifier power: 10-100 watts
Impedance: 8 ohm
Cut Out size: 10.866X7.441"
VX8-W
8” 2-way In-Wall Speaker
Woofer: 8” PP cone, rubber surround, 21.8oz Magnet, 1.4" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 1" silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion Crossover: Phonalic PCB board, 12dB woofer section, 18dB tweeter section, Polymide auto protective reset switch for tweeter
Frequency Response: 39Hz- 22KHz
Sensitivity: 88dB
Recommended amplifier power: 10-125 watts
Impedance: 8 ohm
Cut Out size: 12.815"X8.780"
VX5-LCR
5.25” In-Wall Video Shielded
Left, Center or Right Channel Speaker
Woofer: 5.25” PP cone, rubber surround, 18.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees,19mm silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion
Crossover: Phonalic PCB board, 6dB woofer section, 12dB tweeter section, polymide auto protective reset switch for tweeter
Frequency Response: 55Hz- 22KHz
Sensitivity: 87dB
Recommended amplifier power: 10-125 watts
Impedance: 8 ohm
Cut Out Size: 16.299"X7.411"
VX10-SW
10” In-Ceiling SubWoofer
Woofer: 10” PP cone, rubber surround, 33oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Frequency Response: 23Hz- 500Hz
Sensitivity: 84dB
Recommended amplifier power: 10-200 watts
Impedance: 8 ohm
Cut Out size: 311mm
